Paige Guillaume Hardwood Flooring July 29, 2019 02:51:40
If you choose the Wet Lay method for installing hardwood flooring, you`ll be putting glue across the substrate followed by placing the hardwood panel on top of the glue. After the glue starts to become tacky, you proceed to the next panel. However, sometimes it is recommended for first time installers using the glue down method to place the next panels before the glue becomes tacky so that you can adjust your panels a few minutes later if they are not lined up properly.
Installation Advantages-One other advantage of engineered hardwood floors is that a floating install can be applied directly over vinyl or a concrete slab or any other existing material that is hard and level without the expense and necessity of a subfloor. Manufacturers recommend that a 4-6 mil vapor barrier be installed over the under-surface if moisture is likely to be a problem.
Glue - Many hardwood panel kits come with their own glue. If you need to buy glue for your hardwood panels, I highly recommend Bostik`s Best Adhesive.
Make sure you know your specific type of flooring and finish. You should also be sure to follow the specific manufacturer`s instructions for cleaning and general maintenance. Do some research on how to care for your particular kind of finish. For example, paste wax should never be used on polyurethane finish. Sweeping hardwood floors with a soft broom on a regular basis naturally buffs the surface, therefore protecting it from scratches. Another obvious advantage of this is that it will keep the floor clean. Where possible, leave shoes at the door to avoid dragging extra dirt and grime onto the floor. If not, consider using rugs in high traffic areas such as hallways and entrances to keep feet clean. Remove any solid materials from the floor such as sand, grit and dirt among others. These materials are abrasive and can dull and even scratch the floor`s finish. Use a dry towel to wipe spills and other messes from wood floors. Oils soaps should NEVER be used on hardwood floors. These oils will eventually build up and will dull the surface of the floor. In addition to this, it will make it difficult to refinish the floor whenever needed. Use a vacuum with a bare floor attachment. Such a vacuum easily removes dirt and dust without scratching or otherwise damaging the floor. Do not drag furniture across the floor when moving it. Instead, lift the furniture when moving it. Where dragging is inevitable, invest in a set of slip-mats. Where these are not available, lids from plastic food containers work just as well. Use only cleaners that have specifically been manufactured for use on hardwood floors. Do not substitute with linoleum, laminate or tile cleaners as these can cause the floor to become extra slippery. Use as little water as possible when cleaning wood floors. Wet spots should also be immediately wiped up after cleaning.
Laminate flooring is made of synthetic materials and contains no natural wood products. For this reason, laminate flooring is extremely resistant to moisture. The finish of laminate flooring is plastic-like and extremely durable. Laminate flooring is available in a wide range of colors and finishes that mimic wood flooring, tile, and stone. Laminate flooring is often called a "floating floor," as it does not require the use of glue or nails to adhere it to the subsurface. This is a good choice for areas that see an extremely high traffic volume or are susceptible to scratching or gouging for other reasons, such as pets.
Engineered hardwood flooring is a mix of multiple layers of wood veneers and a synthetic material that are laminated together to form each plank of flooring. This synthetic material serves as the bottom layer and is generally impervious to moisture. This resistance to moisture from below makes this an excellent choice for concrete subfloors and rooms that are below grade. All engineered flooring comes prefinished from the factory. The advantage to prefinished engineered wood flooring is that the factory is often able to coat the finish as many as 7 times or more. This creates an extremely durable surface that will stand up to a great deal of traffic. Still, the top layers of engineered flooring are made of natural wood and can be scratched or damaged by water. Engineered hardwood flooring tends to be much thinner than solid hardwood flooring and it is often glued to the subsurface though it can also be nailed or stapled. The thinner nature of engineered flooring reduces or eliminates the option of refinishing the floors when they wear over time.