Carressa Fontaine Hardwood Flooring July 15, 2019 22:06:45
The Walk On method of installing hardwood flooring requires precise panel laying. This process of installing hardwood flooring waits until the glue is very tacky and then lays the panel in the glue. This keeps you from getting glue smudges all over your panels as you go. Experienced hardwood installers typically use the Walk On method because of the better finished results it can provide. Since you are reading instructions about how to install hardwood floors, we`ll assume you`re using the Wet Lay method.
Carpenter`s Crayon - This is what you use to mark where you`ll make your cuts on your panels. You`ll also use this to mark up the surface where you`ll be laying your panels. You`ll want to keep this handy at all times because it is particularly important with the glue down method that everything be done very precisely.
Make sure you know your specific type of flooring and finish. You should also be sure to follow the specific manufacturer`s instructions for cleaning and general maintenance. Do some research on how to care for your particular kind of finish. For example, paste wax should never be used on polyurethane finish. Sweeping hardwood floors with a soft broom on a regular basis naturally buffs the surface, therefore protecting it from scratches. Another obvious advantage of this is that it will keep the floor clean. Where possible, leave shoes at the door to avoid dragging extra dirt and grime onto the floor. If not, consider using rugs in high traffic areas such as hallways and entrances to keep feet clean. Remove any solid materials from the floor such as sand, grit and dirt among others. These materials are abrasive and can dull and even scratch the floor`s finish. Use a dry towel to wipe spills and other messes from wood floors. Oils soaps should NEVER be used on hardwood floors. These oils will eventually build up and will dull the surface of the floor. In addition to this, it will make it difficult to refinish the floor whenever needed. Use a vacuum with a bare floor attachment. Such a vacuum easily removes dirt and dust without scratching or otherwise damaging the floor. Do not drag furniture across the floor when moving it. Instead, lift the furniture when moving it. Where dragging is inevitable, invest in a set of slip-mats. Where these are not available, lids from plastic food containers work just as well. Use only cleaners that have specifically been manufactured for use on hardwood floors. Do not substitute with linoleum, laminate or tile cleaners as these can cause the floor to become extra slippery. Use as little water as possible when cleaning wood floors. Wet spots should also be immediately wiped up after cleaning.
Durable Coatings-Traditional finishing products are used on engineered hardwood floors, but other finishes are available that are much more durable than the products available for site application. Quality manufacturers apply 7-10 coats of aluminum oxide crystals or diamond dust to make the engineered hardwood finish harder than anything that could be applied on site or even purchased in a Home Depot. Engineered hardwood floors come with as much as a 25-year warranty.
Engineered hardwood flooring is a mix of multiple layers of wood veneers and a synthetic material that are laminated together to form each plank of flooring. This synthetic material serves as the bottom layer and is generally impervious to moisture. This resistance to moisture from below makes this an excellent choice for concrete subfloors and rooms that are below grade. All engineered flooring comes prefinished from the factory. The advantage to prefinished engineered wood flooring is that the factory is often able to coat the finish as many as 7 times or more. This creates an extremely durable surface that will stand up to a great deal of traffic. Still, the top layers of engineered flooring are made of natural wood and can be scratched or damaged by water. Engineered hardwood flooring tends to be much thinner than solid hardwood flooring and it is often glued to the subsurface though it can also be nailed or stapled. The thinner nature of engineered flooring reduces or eliminates the option of refinishing the floors when they wear over time.
Solid hardwood flooring is milled from a single piece of lumber, and it is available either unfinished and prefinished. Unfinished hardwood flooring is sanded, stained, and coated onsite after installation. This method allows for custom stain colors to match a home`s décor, or simply to create a unique appearance. The downside to unfinished flooring is that there is often a considerable mess from sanding the flooring as well as fumes from the stain and urethane coatings. High quality contractors do have equipment that will minimize the dust from sanding process. They may also offer low VOC stains and water-based urethane coatings to reduce the fumes associated with oil-based products. This finishing process can be done multiple time in the future to restore the beauty of the floor as it wears over time. Solid hardwood flooring is best installed over a wood subflooring material as it is generally nailed or stapled to the subsurface. Always install solid wood flooring above grade as it is highly susceptible to moisture and may warp in damp areas.