Robinette Boulanger Hardwood Flooring July 14, 2019 04:33:24
Finishing-Most hardwood floors are sold with some form of factory finish. These consist of protective coats of polyurethane, aluminum oxide, or a combination of both, that are applied to protect the wood from wear and tear. The latest available factory finishes have been formulated to make hardwood flooring more scratch-resistant. In case you purchased unfinished flooring, it will still need to undergo finishing once the floors are installed. However, the quality of the finishing will not be as good as if it were finished in a factory.
Health: because wood doesn`t trap debris in the way carpet does, the air in the house is usually fresher and cleaner. This is especially important for people with allergies or respiratory illnesses who need constant clean air in and around the home.
The glue down method of laying hardwood floors is one of the original methods of installing hardwood flooring. If you want to learn the basics of how to install hardwood flooring using the glue down method, you`ve come to the right place. Among do it yourself hardwood floors, those done with the glue down method can be the most stable and enduring. When you are installing hardwood flooring using the glue down method, you can rest assured that you are using a technique that has been time-tested.
Solid hardwood flooring is milled from a single piece of lumber, and it is available either unfinished and prefinished. Unfinished hardwood flooring is sanded, stained, and coated onsite after installation. This method allows for custom stain colors to match a home`s décor, or simply to create a unique appearance. The downside to unfinished flooring is that there is often a considerable mess from sanding the flooring as well as fumes from the stain and urethane coatings. High quality contractors do have equipment that will minimize the dust from sanding process. They may also offer low VOC stains and water-based urethane coatings to reduce the fumes associated with oil-based products. This finishing process can be done multiple time in the future to restore the beauty of the floor as it wears over time. Solid hardwood flooring is best installed over a wood subflooring material as it is generally nailed or stapled to the subsurface. Always install solid wood flooring above grade as it is highly susceptible to moisture and may warp in damp areas.
The next product in the Impressions hardwood flooring line is a top selling 1/2" thick engineered hardwood called the Salem Series. The Salem series features a Perma-Finish Commercial Grade Water Based finish and is stocked with only Prime Select Grade oak products. The Salem Series has Red Oak & Brazilian Cherry as species available to the name and can be installed below, above & on grade. The Salem Series is an engineered hardwood floor with a hardwood base panel & 2mm thick sawn face wear layer for Oaks & 1.4mm for the Brazilian cherry. The Perma-Finish, being that it is a water base, allows the true coloring of the grain to show through and shine and is added protection against scratching. This product features boards of 1`-4` and an average board length of 31" making it a longer plank than most engineered wood flooring on today`s market. The edges on this product are a 4-sided micro bevel and prevent chipping at the edges while defining the edge of each board. This environmentally friendly hardwood leaves a smaller carbon footprint on the planet due to less waste & less use of domestic trees in the creation of this floor. This is a very thick engineered hardwood and may be sanded and recoated many times over the life of this floor and will last many years. This product is only available in 3" widths for both the Oaks & Brazilian cherry floor. This product can be easily installed either by Glue, Nail or Staple down. The Brazilian Cherry is Lacey Act Compliant being harvested from forests that are used solely for hardwood flooring purposes.
The next engineered collection by Impressions Hardwood is the Traditions Series. This collection brings engineered hardwood flooring to the market with a hand-scraped surface. The Traditions series is a 6" wide by 1/2" thick engineered hardwood with a 2mm sawn face wear layer available in oak or plantation teak. This product is finished with a commercial grade Perma-Finish water based finish to pull the look of the hardwood through the finish to the homeowners view. This artisan hand-scraped finish is done perfectly with no rough ridges, just nice smooth rolling scrapings. The Traditions series Oaks are colored in Rocky mountain or Yellowstone which are two of the most beautiful dark brown colors in the flooring market today, and the Plantation Teak is natural in color. The Teak is a lacey Act Compliant Vintage grade that is hand-picked for a quality floor for the new owner. The Oak is a Vintage Red Oak that is custom crafted for an Old World look and is hand-picked to give this floor the look you want in a nice rustic atmosphere. This product just like the rest of the Impression line sports a 50 year finish warranty & a lifetime Structural warranty. The construction of this product is a hardwood base panel to go along with the thick 2mm wear-layer that can be sanded & refinished 1 time.